启动接口,分配IP地址:
router>
router> enable
router#
router# configure terminal
router(config)#
router(config)# interface Type Port
router(config-if)# no shutdown
router(config-if)# ip address IP-Address Subnet-Mask
router(config-if)# ^z
配置RIP路由协议:30秒更新一次
router(config)# router rip
router(config-if)# network Network-Number <--通告标准A,B,C类网-->
router(config-if)# ^z
配置IGRP路由协议:90秒更新一次
router(config)# router igrp AS-Number <-- AS-Number范围1~65535-->
router(config-if)# network Network-Number <--通告标准A,B,C类网-->
router(config-if)# ^z

配置Novell IPX路由协议:Novell RIP 60秒更新一次
router(config)# ipx routing [node address]
router(config)# ipx maximum-paths Paths <--设置负载平衡,范围1~512-->
router(config)# interface Type Port
router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] <--通告标准A,B,C类网-->
router(config-if)# ^z

配置DDR:
router(config)# dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number]
router(config)# interface bri 0
router(config-if)# dialer-group Group-Number
router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number
router(config-if)# ^z

配置ISDN:
router(config)# isdn swith-type Swith-Type <--配置ISDN交换机类型,中国使用basic-net3-->
router(config-if)# ^z


配置Frame Relay:
router(config-if)# encapsulation frame-relay [cisco | ietf ]
router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ]
router(config-if)# bandwidth kilobits
router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ]
<--配置静态Invers ARP表:
router(config)# frame-relay Protocol Protocol-Address DLCI [ Broadcast ] [ ietf | cisco ] [ payload-compress | packet-by-packet ]
-->
<--设置Keepalive间隔:
router(config-if)# keepalive Number
-->
<--为本地接口指定DLCI:
router(config-if)# frame-lelay local-dlci Number
-->
<--子接口配置:
router(config-if)# interface Type Port.Subininterface-Number [ multipoint | point-to-point ]
router(config-subif)# ip unnumbered Interface
router(config-subif)# frame-lelay local-dlci Number
-->
router(config-if)# ^z

配置标准ACL:
router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] <-- Access-List-Number 范围:1~99标准ACL;100~199扩展ACL;800~899标准IPX ACL;900~999扩展IPX ACL;1000~1099 IPX SAP ACL;600~699Apple Talk ACL-->
router(config)# interface Type Port
router(config-if)# ip access-group Access-List-Number [ in | out ]
router(config-if)# ^z

配置扩展ACL:
router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ]
router(config)# interface Type Port
router(config-if)# ip access-group Access-List-Number [ in | out ]
router(config-if)# ^z

配置命名ACL:
router(config)# ip access-list [ standard | extended ] ACL-Name
router(config [ std- | ext- ] nacl)# [ permit | deny ] [ IP-Access-List-Test-Conditions ]
router(config [ std- | ext- ] nacl)# no [ permit | deny ] [ IP-Access-List-Test-Conditions ]
router(config [ std- | ext- ] nacl)# ^z
router(config)# interface Type Port
router(config-if)# ip access-group [ACL-Name | 1~199 ] [ in | out ]
router(config-if)# ^z

配置DCE时钟:
router# show controllers Type Port <--确定DCE接口-->
router(confin-if)# clock rate 64000 <--进入DCE接口设置时钟速率-->
router(config-if)# ^z

配置PPP协议:
router(config)# username Name password Set-Password-Here <--验证方建立数据库-->
router(config)# interface Type Port
router(config-if)# encapsulation ppp <--启动PPP协议-->
router(config-if)# ppp outhentication [ chap | chap pap | pap chap | pap ] <--选择PPP认证-->
router(config-if)# ppp pap sent-username Name password Password <--发送验证信息-->
router(config-if)# ^z

PAP单向认证配置实例:
验证方:
router-server(config)# username Client password 12345 <--验证方建立数据库-->
router-server(config)# interface serial 0
router-server(config-if)# encapsulation ppp
router-server(config-if)# ppp authentication pap <--选择使用PAP实现PPP认证-->
router-server(config-if)# ^z
被验证方:
router-client(config-if)# encapsulation ppp
router-client(config-if)# ppp pap sent-username Client password 12345 <--发送验证信息-->
router-client(config-if)# ^z

PAP双向认证配置实例:
路由器 A:
routerA(config)# username B password 12345
routerA(config)# interface serial 0
routerA(config-if)# encapsulation ppp
routerA(config-if)# ppp authentication pap
routerA(config-if)# ppp pap sent-username A password 54321
routerA(config-if)# ^z
路由器 B:
routerB(config)# username A password 54321
routerB(config)# interface serial 1
routerB(config-if)# encapsulation ppp
routerB(config-if)# ppp authentication pap
routerB(config-if)# ppp pap sent-username B password 12345
routerB(config-if)# ^z

[1] [2] [3] 下一页  

文章录入:csh    责任编辑:csh 


CHAP单向认证配置实例:
验证方:
router-server(config)# username router-client password 12345
router-server(config)# interface serial 0
router-server(config-if)# encapsulation ppp
router-server(config-if)# ppp authentication chap
router-server(config-if)# ^z
被验证方:
router-client(config-if)# encapsulation ppp
router-client(config-if)# ppp authentication chap
router-client(config-if)# ppp chap hostname router-client
router-client(config-if)# ppp chap password 12345
router-client(config-if)# ^z

CHAP双向认证配置实例:
路由器 A:
routerA(config)# username routerB password 12345
routerA(config)# interface serial 0
routerA(config-if)# encapsulation ppp
routerA(config-if)# ppp authentication chap
routerA(config-if)# ppp chap hostname routerA

routerA(config-if)# ppp chap password 54321
routerA(config-if)# ^z
路由器 B:
routerB(config)# username routerA password 54321
routerB(config)# interface serial 1
routerB(config-if)# encapsulation ppp
routerB(config-if)# ppp authentication chap
routerB(config-if)# ppp chap hostname routerB
routerB(config-if)# ppp chap password 12345
routerB(config-if)# ^z

Telnet使用:
routerA# terminal monitor <--可以传回在远端主机执行Debug命令的结果-->
routerA# telnet IP-Address [ Router-Name ] <--Telnet到指定的地址或名字的主机-->
routerB# [ exit | logout ] <--退出Telnet-->
routerB# ++<6>再按 <--挂起Telnet-->
routerA# show sessions <--显示当前所有Telnet的信息,包括Connect-Number -->
routerA# Connect-Number  <--返回指定的Telnet连接-->
routerA# disconnect IP-Address [ Router-Name ] <--断开指定地址或名字的主机的连接-->
routerA# show user <--显示Telnet到本机的连接信息-->
routerA# clear line [ 0 | 1 | 2 | 3 | 4 ] <--断开指定Telnet到本机的连接-->


禁止任何Telnet到本机:
router(config)# line vty 0 4
router(config-line)# access-class ACL-Number
router(config)# ^z

设置主机名:
router(config)# hostname Set-Hostname
router(config)# ^z
router(config)# ^z

设置用户模式密码:
router(config)# line console 0
router(config-line)# login
router(config-line)# password Set-Password
router(config-line)# ^z
设置Telnet密码:
router(config)# line vty 0 4
router(config-line)# login
router(config-line)# password Set-Password
router(config-line)# ^z

设置特权模式密码:
router(config)# enable password Set-Password <--不加密的密码,明码-->
router(config)# enable secret Set-Password <--经过加密的密码-->
router(config)# ^z

给所有密码加密:
router(config)# service password-ancryption Set-Password-Here
router(config)# no service password-ancryption <--取消加密-->
router(config)# ^z

设置登录Banner:
router(config)# banner motd 分隔符 Set-Banner-Information-Here 分隔符 <--前后分隔符一定要一致-->

设置接口的描述信息:
router(config-if)# description Set-Port-Information-Here
router(config)# ^z

CDP的控制:
router(config-if)# cdp enable <--在指定端口启用CDP,缺省-->
router(config-if)# no cdp enable <--在指定端口关闭CDP-->
router(config)# cdp run <--使所有端口启用CDP-->
router(config)# no cdp run <--使所有端口关闭CDP-->


Ping的使用:
router# ping IP-Address
router# ping  <--扩展Ping命令-->
Protocol [ip]:[ Protocol-Type ] <--选择协议类型-->
Target IP address:IP-Address <--输入测试地址-->
Repeat count [5]: <--选择发送的ICMP包数量-->
Datagram size [100]: <--选择每个包的大小-->
Timeout in seconds [2]: <--设置每个包的超时时间-->
Extended commands [n]:y <--使用扩展Ping命令-->
Sweep range of sizes [n]:

Tracke的使用:
router# trace IP-Address [ Host-Name ]

为Cisco 4000路由器指定媒体类型:
router(config-if)# media-type 10baset <--使AUI(默认)失效,改为使用RJ-45-->
router(config-if)# ^z

更改路由器启动顺序:
router(config)# boot system flash IOS-FileName
router(config)# boot system tftp IOS-FileName TFTP-IP-Address
router(config)# boot system rom
router(config)# ^z

修改寄存器数值:
router(config)# config-register value <--Cisco出厂默认value=0x2102,value范围:0x2100(进入ROM监视器),0x2101(使系统从ROM启动),0x2102~0x210F(使系统从NVRAM启动)。0x1=0x2101,从最小位开始改变-->

在ROM监视器中更改寄存器数值:
> o/r value

路由器密码的恢复:
冷关机,然后再开机并在60秒内按< Ctrl>+进入ROM监视器模式
> o/r 0x2142 <--25xx型路由器--> 或 > confreg 0x2142 <--16xx型路由器-->
router> I
router> n
router> enable
router# copy startup-config running-config
router# configure terminal
router(config)# enable secret New-Password
router(config)# config-register 0x2102
router(config)# ^z
router# copy running-config startup-config
router# reload

配置名称-主机入口:
router(config)# ip host Set-Name [ TCP-Port-Number ] IP-Address [ IP-Address 2 ]...
router(config)# ^z

上一页  [1] [2] [3] 下一页  

文章录入:csh    责任编辑:csh 

定义DNS主机:
router(config)# ip name-server Server-Address [ Server-Address 2 ]...
router(config)# ^z

禁用DNS:
router(config)# no ip domain-lookup
router(config)# ^z

配置水平分割:
router(config-if)# ip split-horizon
router(config-if)# no ip split-horizon
router(config-if)# ^z

配置静态路由:
router(config)# ip route IP-Address Subnet-Mask [ Next-Hop-Address | Local-Out-Port ] [Distace ]
<--Distance范围:1~255,相当于优先权,越小越好。RIP=120;DSPF=110;IGRP=100;EIGRP=90-->
router(config)# ^z

配置缺省路由:
router(config)# ip defoult-network IP-Address <--动态缺省路由-->
router(config)# ip route 0.0.0.0 0.0.0.0 [ Next-Hop-Address | Local-Out-Port ] [Distace ] <--静态缺省路由-->
router(config)# ^z

其它命令:
router# show version
router# show running-config
router# show startup-config
router# show flash
router# show interface [ Type Port ]
router# show buffers
router# show protocol
router# show mem
router# show stacks
router# show processes
router# show cdp entry [ Device-Name ] <--显示指定邻居三层信息-->
router# show cdp neighbors
router# show cdp neighbors detail <---显示所有邻居三层信息->
router# show ip router
router# show ipx router
router# show host
router# show ip protocol
router# show ip interface Type Port
router# show ipx interface Type Port
router# show ipx servers
router# show ipx traffic
router# show access-lists [ ACL-Number ]
router# show isdn status
router# show dialer <--查看ISDN拨号信息-->
router# show isdn active
router# show frame-relay pvc
router# show frame-relay map
router# show frame-relay lmi
router# erase startup-config
router# reload
router# setup
router# copy running-config startup-config
router# copy startup-config running-config
router# copy tftp running-config
router# copy running-config tftp
router# debug ipx routing activity
router# debug ipx sap
router# debug isdn q921
router# debug isdn q931
router# debug dialer
router# debug ip rip
router# clear interface bri [ 0 | 1 | 2 ]

上一页  [1] [2] [3] 

文章录入:csh    责任编辑:csh 

以上就是【思科路由器基本配置与常用配置命令simple for CCNA】的全部内容了,欢迎留言评论进行交流!

赞(0) 踩(0)
发表我的评论

最新评论

  1. 暂无评论